Aod transmission hookup

aod transmission hookup

Can you put an AOD transmission in a classic Mustang?

The most common transmission swap with older Fords is from a C4, C6, or FMX to an AOD or manual 5-speed. The focus here is putting a Ford AOD into a classic Mustang and other vintage Ford applications, which are the more common swaps.

What kind of transmission is the AOD?

The AOD was used originally on 80s and early-90s Ford, Lincoln and Mercury products and in the F-series pickups and E-series vans as well. The AOD can be a relatively easy transmission to transplant and the additional 4th-gear overdrive can give you added fuel savings, especially in cars and trucks using taller rear axle ratios.

How do I find the AOD code on a Ford transmission?

Ford lists their transmission codes on their Vehicle Certification Label and these are a single letter located along the bottom of the label under the abbreviation TR or TRANS. The AOD transmissions will carry a T designation for any rear-wheel drive vehicles. Lastly, you can also check the tag attached to the transmission itself.

What size flex plate does a Ford AOD transmission have?

The AOD takes a 164-tooth AOD-specific flexplate instead of the smaller 157-tooth pieces common to the C4 and early Ford manual transmissions. Because the AOD is longer, the crossmember must position the mount farther to the rear of the vehicle to support the transmission.

Can you put a Ford AOD in a classic Mustang?

The focus here is putting a Ford AOD into a classic Mustang and other vintage Ford applications, which are the more common swaps. If you’re going from a C4 to an AOD with a small-block V-8 application, it is important to understand the differences between them.

Does a Ford AOD transmission need a computer?

Because Ford used these transmissions in so many production vehicles, the Ford AOD is relatively easy to locate at a used parts yard and can be purchased for a reasonable price. The Ford AOD does not need a computer to function properly either.

What kind of transmission does a 60s and 70s Ford use?

Probably one of the most popular transmission exchanges that are being performed on 60s and 70s Ford cars and trucks involves using the Ford AOD or automatic overdrive. The AOD was used originally on 80s and early-90s Ford, Lincoln and Mercury products and in the F-series pickups and E-series vans as well.

What size flex plate does a Ford AOD transmission have?

The AOD takes a 164-tooth AOD-specific flexplate instead of the smaller 157-tooth pieces common to the C4 and early Ford manual transmissions. Because the AOD is longer, the crossmember must position the mount farther to the rear of the vehicle to support the transmission.

What size is a flex plate on a Ford AOD?

You replace it with the 164-tooth flexplate for the AOD/AODE/4R70W, which is also a 28-ounce offset balanced. Note the type of engine you have also determines the flexplate type. Small-block Ford V-8s, which are externally balanced, are either 28- or 50-ounce offset balanced.

What kind of flywheel does a AOD transmission have?

AOD transmissions used a 164 tooth flexplate. Mustang T5 transmissions used a 157 tooth flywheel and a 10.5 or 10 clutch disc. Ford light-duty trucks often used a 164 tooth flexplate and an 11 clutch disc, though some heavy-duty trucks used much larger clutches.

Which AOD flexplate do I need for my AOD?

If youre swapping an AOD onto an 81 or later 5.0 youll need the AOD flexplate (164 teeth, 50.0 oz-in balance factor, for 5.0 with AOD applications) OEM part number E2AZ-6375-A.

What kind of flex plate does a Ford truck use?

Ford light-duty trucks often used a 164 tooth flexplate and an 11 clutch disc, though some heavy-duty trucks used much larger clutches. C4 transmissions could have used any of the three tooth count flexplates depending on the bellhousing used.

Related posts: